The B&W Companion 5th Wheel Trailer Hitch w/ Slider # BWRVK3400-5W weighs about 282 lbs while the Custom Underbed Installation Kit # BWGNRK1116-5W for your 2019 Ford F-250 Super Duty weighs in at about 143 lbs. I reached out to my contact at B&W who confirmed this so you will be adding about 425 lbs to your pickup.
Since you don't have the factory towing system installed I recommend adding the Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring Harness with 7-Pole Plug # 41157 as well.... view full answer...
The Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers # 325-GH-624 has a shipping weight of 60 lbs. If you remove a few pounds for the shipping materials then that brings the product weight to about 57 lbs. view full answer...
While I don't know the bolt pattern of the coupler on your 1996 Demco Car Trailer I did go ahead and have the # DM12925 pulled from the warehouse and measured it so I could give you this diagram to see if it matches your coupler. If this doesn't match your trailer we could try to keep looking for something that would, but manufacturers most likely have changed their bolt patterns since the 90's so we may still end up having to drill new holes. view full answer...
Yes, you can and it'll allow you to keep the one on your bumper. I recommend the Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector item # C57010. This harness puts a 7-way connector in the bed of your 2024 Ford F-250 and makes hooking up to your gooseneck or 5th wheel trailer easier and more convenient.
I have attached a picture below along with an installation video to help you get this 7-way harness set up and show you what it looks like once installed. view full answer...
There's only one set of air bags that is compatible with the B&W Turnover Ball System item # BWGNRK1108 and your 1999 F-250. It is the Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers item # AL88390. All of the other air bag kits are blocked by the brackets used to install the gooseneck hitch. So to answer your question there are no Firestone kits that will work with an in bed hitch of any kind on your F-250.
The center bolt for the upper air bag bracket... view full answer...
The distance between the center of the ball hole and the hitch pin hole of the Convert-A-Ball Dual-Cushioned, Adjustable Ball Mount # CAB-UM is 11 inches. view full answer...
There are a couple of options to lift your trailer depending on if your axle's sit above or below the leaf springs.
If your axles are already below your leaf springs the only option is the Correct Track Trailer Alignment and Lift Kit item # RR23QX. This kit mounts to your spring hangers and moves the attachment point down 1-1/4" or 2-1/4".
If your springs are below your axles you will want to use one of our axle flip kits. These work by moving your axle below your springs and give you... view full answer...
We don't have a way to add a bulb seal to the Rubber Wiper Seal for RV Slide Out 4-1/16" Wide item # SR46FR you were looking at. There is a 3-3/16" Wide Rubber Wiper Seal with a Bulb it is item # SR48FR. view full answer...
With the 2022 Ford F-250 Super Duty, you can definitely mount ladders and other cargo that extend over the cab of your truck using the Thule TracRac TracONE # TH27000XTB. This is because the crossbars are higher than the cab. I went ahead and attached photos from neighbors who left 5-star reviews of their TracONEs hauling a long ladder and a kayak.
It is important to note that the TracONE is not compatible with with most tonneau covers. If you have a tonneau cover on your truck that does... view full answer...
Since you will be adding an obstacle next to the rear sensors on your 2016 Ford F-250 Super Duty the Access Rockstar XL Custom Mud Flaps # A10100221 could very likely set off the proximity sensors.
These mud flaps weigh about 45 lbs and the Rock Tamers Heavy-Duty, Adjustable Mud Flap System # ERT00108 weighs slightly over 30 lbs.
To ensure that your rear sensors are not set off by your mud flaps I recommend installing permanent mud flaps. We have the WeatherTech Mud Flaps # WT120031 if... view full answer...
The springs in kit # TFR250SDJ are 4-1/2 inches tall and for kit # TFRTT350J they are 3-9/16 inches tall. These measurements do not include the mounting brackets that attach to the bottoms of the frame which are approximately 2-3/8 inches tall.
The Timbren # TFRTT350J are designed more for commercial duty where your truck bed stays loaded for long periods of time.The Timbren # TFR250SDJ is a more standard duty spring that is ideal for towing applications where you may be experiencing a... view full answer...
The mounting bolt pattern for the Buyers Products 3" I.D. Heavy-Duty Forged 4-Bolt Mount Lunette Ring # 337BDB1385 that you referenced is 4-1/2 inches square. view full answer...
The Weigh Safe 180 Hitch 2-Ball Mount # LTB6-3 has a total weight (with the ball platform attached) of just 22 pounds. The shank by itself is only 8 pounds. You are right that the aluminum shank allows it to weigh less than all steel options such as the B&W Tow and Stow # BWTS30040B that weighs closer to 40 pounds.
I have attached a short video demonstration that you can check out as well. view full answer...
I have added a cut out which shows the dimensions of the monitor of the Furrion Vision S Wireless RV Backup Camera System with Night Vision - Rear Mount - 4.3" Screen # FOS43TASF.
Overall, the monitor is 4-3/4 inches wide, 2-1/8 inches tall, and 1 inch deep. view full answer...
Since your 2000 Ford F-250 has the B&W item # BWGNRK1108 installed, you will need to use the Firestone Ride-Rite Air Helper Springs item # F2550. This air bag system is compatible with B&W gooseneck hitches. It has a 5,000 lbs load leveling capacity and requires no drilling for installation.
I have linked an installation video below to help you get this air bag system set up.
I also recommend adding the Firestone Air Command item # F2610 to your truck. This onboard compressor will allow... view full answer...
Yes, you can use the Curt Rota-Flex 5th Wheel Pin Box item # LC328329 with the Sliding B&W Companion 5th Wheel Trailer Hitch # BWRVK3400 or the Fixed item # BWRVK3500. Both of these hitches will work with your F-250's Turnover ball system. Since you have the shorter bed length I recommend using the slider.
The Curt Rota-Flex 5th Wheel Pin Box item # LC328329 will replace a Lippert 1621 pin box and has a 21,000 lbs capacity.
To make towing with a 5th wheel easier, I recommend adding the... view full answer...
The Mighty Cord Replacement Hardwire RV Plug # A10-R30VP that you referenced measures 4-1/2 inches long by 2-1/2 inches wide and is 2 inch thick. view full answer...
The 18k Demco Hijacker Autoslide, part # DM8550024, weighs right around 300 pounds and the 21k model, part # DM8550038, is closer to 330 pounds. Both of these hitches fit right into the factory puck system of your 2019 Ford F-250. I've linked a video of them both for you to take a look at.
If you're looking for a lighter hitch I recommend the B&W Companion, part # BWRVK3370. It also fits right into the pucks in your Ford's bed and weighs about 260 pounds. Plus, it's pretty easy to... view full answer...
I attached a few pictures with several dimensions for the SolidStep Manual Fold-Down Steps # LC678025 that you referenced.
It should cover all the possible dimensions you'd need. view full answer...
I have a solution for you, but the bracket height of the Dutton-Lainson Round Trailer Jack # DL22210 has a bracket height of 16-5/8", so it would not be short enough to be used on your trailer. I recommend usinig the Fulton F2 Swing-Up Trailer Jack # F1413020134 which has an adjustable bracket that when at its lowest setting is approximately 11" from the ground to the center of the bracket. This is a dual wheel, swiveling jack that can provide up to 10" of lift and has a 1600-lbs capacity.... view full answer...
Go To Results